Bartell B430 Manuale delle Istruzioni Scaricare il pdf (Pagina 10)

EDGER TROWEL INSTRUCTION MANUAL

BARTELL MORRISON INC.

375 ANNAGEM BLVD, MISSISSAUGA, ONTARIO, CANADA, L5T 3A7, 905-458-5455 FAX 905-458-5484

Created: 07/04

Revised: 08/09

- 10 -

STARTING PROCEDURE:

*WARM CLIMATE

Open fuel valve on gas tank. Set throttle lever to “Fast”

idle position, set choke to closed position, start engine.

Open choke slightly to prevent flooding. Move to “Open”

or “Run” position when engine is warm, increase throttle

to maximum operation position (3600 rpm).

STARTING PROCEDURE:

*COLD CLIMATE

Follow same procedure as above but allow longer

warm-up period – 3 to 5 minutes. In cold weather, oil is

much heavier to move and requires more time to work

its way into the moving parts. If maximum power is not

attained, allow further warm-up time.

STOPPING PROCEDURE

1. Throttle engine down.

2. Turn off stop switch.

MAINTENANCE

Maintaining your Edger Power Trowel will insure long

life to the machine and its components.

AIR CLEANER - Keep air filter clean at all times.

Wash away dust and debris using a non-oil based

cleaning solvent. Let the filter dry before re-installing.

LUBRICATION – Always check engine oil regularly.

Use proper engine oil as recommended. See chart on

this page. Fill crankcase to levels as recommended in

manufacture’s engine manual.

SPARK PLUG

–

Check and clean spark plugs

regularly. A fouled, dirty or carboned spark plug

causes hard starting and poor engine performance.

Set spark plug gap to recommended clearance. Refer

to engine manual.

BELT TENSION – IMPORTANT!

When the engine is switched off, and the machine has

stopped, the normal belt play should be loose. This is

due to the clutch type. When the machine is running

at full throttle, the clutch will close in, which tightens

the belt causing the gearbox to engage.

When adjusting the belt make sure that the clutch is in

alignment with the follower pulley. Secure belt guard.

Tighten all engine mount bolts, and tighten lock nuts.

TRANSPORTING

When transporting the trowel, always keep the handle

folded and the blades flat on the floor to prevent

damage to the pitch control system. Always keep the

floating disc underneath the blades to protect them

against damage.

CAUTION:

Never lift the trowel by the rotating ring; use the

hoist hook or handle provided on the trowel.

Remove the float disc when lifting machine more

than 100cm (40in). The floating disc could fall off.

LUBRICATION

1. ENGINE OIL

The long life and successful operation of any piece of

machinery is dependent on frequent and thorough

lubrication.

Before using the trowel, always check your engine for

oil. Use proper engine oil as recommended in the

engine manufacturer’s manual. Fill crankcase to

levels as recommended.

ENGINE OIL SPECIFICATIONS

Season Temperature

Grade of Engine Oil

Spring to Autumn

+40°F (4°C) to +120°F (49°C)

Winter

+15°F (-9°C) to +40°F (4°C)

Below +15°F (-9°C) SAE 10W-30

SAE 30

SAE 20

2. SPIDER PLATE

The trowel arm on the spider plate does not require

lubrication. If a trowel arm becomes jammed, this is

probably due to a bent arm, which will require

replacement. Appropriate “winterize” steps should be

taken if the machine is going to be stored for long

periods of time.

3. GEARBOX

In operation the gearbox lubricant is in a fluid state.

When the machine is stopped the lubricant returns to

a gel state. It will only be necessary to inspect the

sealed components if the outside of the gearbox gets

too oily or otherwise shows evidence of a leak. If this

happens, clean the machine thoroughly and look for

leaks. Effect necessary repairs immediately. Use

SHELL TIVELA COMPOUNDS ‘A’ (0.3L, 10.1oz.)

gear oil or equivalent to top up the gear box after any

maintenance to the internal components.

STORAGE

The following steps should be taken to prepare your

Edger Power Trowel for extended storage.

1. Close fuel shut off valve.

2. Siphon excess gasoline from tank.

3. Start engine until it stops from lack of fuel. This will

use up all the fuel in the carburetor and prevent

formation of deposits due to evaporation of fuel.

4. Remove spark plug and pour 2 oz. of SAE-30 or

SAE-40 motor oil into the cylinder. Slowly crank the

engine 2 or 3 times to distribute the oil throughout the

cylinder. This will help prevent rust during storage.

Replace spark plug.

Store the unit in an upright position in a cool, dry,

well ventilated area.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 24 25

Commenti su questo manuale

Nessun commento

Bartell B430 Manuale delle Istruzioni Pagina 10

Commenti su questo manuale